banner



How To Install A Delta Tub And Shower Valve

Delta shower valve installation doesn't take to be hard.

That said, if local plumbing code requires the use of copper, this tutorial volition exist a huge help.

There are tons of tips that'll brand your project much easier, so let's dive in!

Delta Shower Valve Installation Supplies

Here are the supplies used in this project:

  • Delta MultiChoice Rough-In Valve
  • Bernzomatic MAP Gas
  • TS400 Trigger Start Torch
  • H-20 Water Soluble Flux
  • Acid Brush for Flux
  • Oatey Safe-Flo Solder
  • Emery Cloth
  • Nylon Grit Pads
  • Ridgid Deburring Tool
  • Sioux Chief AA MiniResters (H2o Hammer Arrester)
  • Blazon L one/2″ Copper
  • Flame Protector Pads

Don't worry, I'll show you how to use all these materials.

How to Set Delta Shower Valves to Right Depth

Setting any shower valve to the correct depth is important.

Adhere a scrap piece of the backer board to the stud walls. Then dry fit the tile being used and place the valve inside the wall (flush with the adjacent wall).

Get the measurement from the end of the plaster guard to the finished wall.

Delta Shower Valve Depth

This measurement is the depth of the wood blocking that's needed to set the valve at the right depth.

Delta valves typically but need a piece of two×four or 2×ten dimensional lumber, which can be nailed or screwed to studs.

Connect Copper Riser Pipe to Delta Valve

The first pace to installing a Delta shower valve is to connect the riser pipage.

Deburr and prep the copper pipe with emery cloth or nylon grit pads.

Then apply the Oatey H-20 flux to both the pipe and drop-ear elbow; this is a great option because it's water-soluble.

In add-on, the water lines won't demand to be flushed when using H-20 flux.

I like to overhang the pipe on two pieces of ii×6 and solder information technology with a torch.

Riser Pipe for Delta Shower Valve

This keeps the workspace safety and provides ample working room for the torch.

Let that cool and wipe off any backlog flux.

How to Prep Copper Pipes for Delta Shower Valve

Copper pipage prep is the fundamental to getting nifty soldered joints.

The first pace is to deburr both the inside and outside of the pipe.

Then to utilize either emery cloth or nylon grit pads to clean the copper.

Fittings are normally very clean but information technology doesn't hurt to use a wire brush.

Finally, apply a thin layer of the Oatey H-xx flux to the pipage and plumbing equipment. Once the fitting is placed on the pipe, wipe off any excess flux.

How to Apply Flux to Copper Pipe

This terminal tip will aid you lot get awesome-looking soldered joints.

How to Solder Copper Pipes to Delta Shower Valves

Information technology's good practice to beginning the rut at the bottom and piece of work upward.

Therefore, I recommend heating the couplings first and so working up toward the valve.

As well, pre-estrus the kickoff half-inch of the copper pipe (just for a few seconds) and so use rut to the fitting.

Soldering Copper Pipe

Dab the solder on the fitting/pipe connection and once information technology starts to melt, remove the oestrus.

This absolutely takes some practise, then it never hurts to do just that – exercise with spare pieces of copper and fittings.

Watch this total tutorial to see all the steps for a Delta shower valve installation with copper pipe

What'due south Next

Hopefully, the tips in this tutorial help you with your shower remodel. If your side by side step is to waterproof the shower, this Schluter tutorial might help out.

If you're doing a bathroom remodel and need help, bring together ane of my step-by-footstep online courses – information technology'll make your bath renovation much easier!

Let me know if yous accept any questions and I'll do my best to aid.

Hope you have an awesome day!

Cheers,

Jeff

Minor Bath Remodel Tips

Source: https://homerepairtutor.com/delta-shower-valve-installation-tips/

Posted by: browningthoureprot.blogspot.com

0 Response to "How To Install A Delta Tub And Shower Valve"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel